WP43 News

This area is for discussion about these families of custom high-end Scientific Calculator applications for SwissMicros devices.
User avatar
Walter
Posts: 3070
Joined: Tue May 02, 2017 11:13 am
Location: On a mission close to DRS, Germany

Re: 43S News

Post by Walter »

PierreMengisen wrote:
Sat Jul 10, 2021 1:42 pm
And what do you think about the 3.8 dimension?
So-called over-designing should be avoided. The 3.8 can be calculated via (70.5 - 2x3.65 - 6x7.7)/5, so it should not be stated on the drawing.
WP43 SN00000, 34S, and 31S for obvious reasons; HP-35, 45, ..., 35S, 15CE, DM16L S/N# 00093, DM42β SN:00041
User avatar
PierreMengisen
Posts: 305
Joined: Wed Nov 29, 2017 1:38 pm
Location: Neuchâtel CH

Re: 43S News

Post by PierreMengisen »

RefMan P B-30
Is the command FILL in the b/w print at the rear correct ? The current feature of the Windows version is STATUS :?:
Pierre
[TI59 with PC100C; TI-84 Plus CE-T; HP41CV with HP IL loop & 2*82161A DCD & 82162 TP; HP15C; HP28S; DM41; DM41L; DM42; DM41X]
User avatar
Walter
Posts: 3070
Joined: Tue May 02, 2017 11:13 am
Location: On a mission close to DRS, Germany

Re: 43S News

Post by Walter »

PierreMengisen wrote:
Sat Jul 10, 2021 1:57 pm
RefMan P B-30
Is the command FILL in the b/w print at the rear correct ? The current feature of the Windows version is STATUS :?:
The current feature of the Windows version should be FILL. Which version do you use? (Please call VERS?)
WP43 SN00000, 34S, and 31S for obvious reasons; HP-35, 45, ..., 35S, 15CE, DM16L S/N# 00093, DM42β SN:00041
User avatar
PierreMengisen
Posts: 305
Joined: Wed Nov 29, 2017 1:38 pm
Location: Neuchâtel CH

Re: 43S News

Post by PierreMengisen »

Walter wrote:
Sat Jul 10, 2021 1:57 pm
PierreMengisen wrote:
Sat Jul 10, 2021 1:42 pm
And what do you think about the 3.8 dimension?
So-called over-designing should be avoided. The 3.8 can be calculated via (70.5 - 2x3.65 - 6x7.7)/5, so it should not be stated on the drawing.
So please indicate only once the 3, the 5.3 and the 30.
Pierre
[TI59 with PC100C; TI-84 Plus CE-T; HP41CV with HP IL loop & 2*82161A DCD & 82162 TP; HP15C; HP28S; DM41; DM41L; DM42; DM41X]
User avatar
Walter
Posts: 3070
Joined: Tue May 02, 2017 11:13 am
Location: On a mission close to DRS, Germany

Re: 43S News

Post by Walter »

PierreMengisen wrote:
Sat Jul 10, 2021 2:04 pm
Walter wrote:
Sat Jul 10, 2021 1:57 pm
PierreMengisen wrote:
Sat Jul 10, 2021 1:42 pm
And what do you think about the 3.8 dimension?
So-called over-designing should be avoided. The 3.8 can be calculated via (70.5 - 2x3.65 - 6x7.7)/5, so it should not be stated on the drawing.
So please indicate only once the 3, the 5.3 and the 30.
This complaint should go to SwissMicros for reasons stated above.
WP43 SN00000, 34S, and 31S for obvious reasons; HP-35, 45, ..., 35S, 15CE, DM16L S/N# 00093, DM42β SN:00041
User avatar
PierreMengisen
Posts: 305
Joined: Wed Nov 29, 2017 1:38 pm
Location: Neuchâtel CH

Re: 43S News

Post by PierreMengisen »

Walter wrote:
Sat Jul 10, 2021 2:01 pm
PierreMengisen wrote:
Sat Jul 10, 2021 1:57 pm
RefMan P B-30
Is the command FILL in the b/w print at the rear correct ? The current feature of the Windows version is STATUS :?:
The current feature of the Windows version should be FILL. Which version do you use? (Please call VERS?)
0.20.4
ver.png
ver.png (40.73 KiB) Viewed 1816 times
Pierre
[TI59 with PC100C; TI-84 Plus CE-T; HP41CV with HP IL loop & 2*82161A DCD & 82162 TP; HP15C; HP28S; DM41; DM41L; DM42; DM41X]
User avatar
PierreMengisen
Posts: 305
Joined: Wed Nov 29, 2017 1:38 pm
Location: Neuchâtel CH

Re: 43S News

Post by PierreMengisen »

Walter wrote:
Sat Jul 10, 2021 2:07 pm
PierreMengisen wrote:
Sat Jul 10, 2021 2:04 pm
Walter wrote:
Sat Jul 10, 2021 1:57 pm

So-called over-designing should be avoided. The 3.8 can be calculated via (70.5 - 2x3.65 - 6x7.7)/5, so it should not be stated on the drawing.
So please indicate only once the 3, the 5.3 and the 30.
This complaint should go to SwissMicros for reasons stated above.
Then you must indicate in your manual that this figure is the responsibility of SwissMicros!
Last edited by PierreMengisen on Sat Jul 10, 2021 2:31 pm, edited 1 time in total.
Pierre
[TI59 with PC100C; TI-84 Plus CE-T; HP41CV with HP IL loop & 2*82161A DCD & 82162 TP; HP15C; HP28S; DM41; DM41L; DM42; DM41X]
User avatar
Walter
Posts: 3070
Joined: Tue May 02, 2017 11:13 am
Location: On a mission close to DRS, Germany

Re: 43S News

Post by Walter »

PierreMengisen wrote:
Sat Jul 10, 2021 2:17 pm
Walter wrote:
Sat Jul 10, 2021 2:07 pm
PierreMengisen wrote:
Sat Jul 10, 2021 2:04 pm
So please indicate only once the 3, the 5.3 and the 30.
This complaint should go to SwissMicros for reasons stated above.
Then you must indicate in your manual that this figure is the responsibility of SwissMicros!
Mais oui, monsieur! Please read p. 2 though.
WP43 SN00000, 34S, and 31S for obvious reasons; HP-35, 45, ..., 35S, 15CE, DM16L S/N# 00093, DM42β SN:00041
User avatar
Walter
Posts: 3070
Joined: Tue May 02, 2017 11:13 am
Location: On a mission close to DRS, Germany

Re: 43S News

Post by Walter »

PierreMengisen wrote:
Sat Jul 10, 2021 2:09 pm
Walter wrote:
Sat Jul 10, 2021 2:01 pm
PierreMengisen wrote:
Sat Jul 10, 2021 1:57 pm
RefMan P B-30
Is the command FILL in the b/w print at the rear correct ? The current feature of the Windows version is STATUS :?:
The current feature of the Windows version should be FILL. Which version do you use? (Please call VERS?)
0.20.4
ver.png
Just tested. If you download, extract, and run WP43S 0.20.4. in a new directory, everything is fine: FILL is f-shifted ENTER as it should be.
WP43 SN00000, 34S, and 31S for obvious reasons; HP-35, 45, ..., 35S, 15CE, DM16L S/N# 00093, DM42β SN:00041
User avatar
PierreMengisen
Posts: 305
Joined: Wed Nov 29, 2017 1:38 pm
Location: Neuchâtel CH

Re: 43S News

Post by PierreMengisen »

Walter wrote:
Sat Jul 10, 2021 2:57 pm
PierreMengisen wrote:
Sat Jul 10, 2021 2:17 pm
Walter wrote:
Sat Jul 10, 2021 2:07 pm

This complaint should go to SwissMicros for reasons stated above.
Then you must indicate in your manual that this figure is the responsibility of SwissMicros!
Mais oui, monsieur! Please read p. 2 though.
Non Monsieur puisque vous l'avez modifiée !
Pierre
[TI59 with PC100C; TI-84 Plus CE-T; HP41CV with HP IL loop & 2*82161A DCD & 82162 TP; HP15C; HP28S; DM41; DM41L; DM42; DM41X]
Post Reply