Search found 18 matches

by jwhsu
Fri Apr 03, 2020 4:39 pm
Forum: Update Announcements
Topic: DM41X v1.11t08: 2020-03-30
Replies: 9
Views: 577

Re: DM41X v1.11t08: 2020-03-30

Just updated, no issues. Really like the module map. Really helps with figuring out which port the module is plugged into and identifying conflicts. Thanks.
by jwhsu
Sat Feb 29, 2020 8:40 pm
Forum: Software issues
Topic: Cannot program byte grabber
Replies: 26
Views: 1246

Re: Cannot program byte grabber

Can report that you can now create the Byte Grabber program with the DM41 1.11t02 update. Thanks.
by jwhsu
Wed Feb 26, 2020 11:34 pm
Forum: Software issues
Topic: Hepax/Zenrom conflict
Replies: 5
Views: 335

Re: Hepax/Zenrom conflict

rprosperi wrote:
Wed Feb 26, 2020 8:57 pm
HEPAX/ZenROM problem found and fixed. An updated BETA build will posted in the next couple days.

Please don't waste bandwidth hitting refresh, these bug fixes are not so exciting ;)
Thank you. Cannot wait to try it out.
by jwhsu
Fri Feb 21, 2020 4:50 pm
Forum: Software issues
Topic: Hepax/Zenrom conflict
Replies: 5
Views: 335

Re: Hepax/Zenrom conflict

here is the rominit.log sequence 1) Zenrom, 2) Hepax: 0-0: SM_NUT-CXX.mod pg:0 R[0] 0 0 1 0 NUT0-N R[1] 1 0 1 0 NUT1-F R[2] 2 0 1 0 NUT2-L_X R[3] 3 0 1 1 -EXT FCN 2X R[4] 5 0 1 1 -TIME 2X R[5] 5 0 2 1 -X/F_BKN2 0-1: ZENROM.MOD pg:9 0-2: HEPAX_4H.MOD pg:8 1-0: SM_NUT-CXX.mod pg:0 1-1: ZENROM.MOD pg:9...
by jwhsu
Fri Feb 21, 2020 4:40 pm
Forum: DM41X
Topic: DM41X Beta Programme
Replies: 326
Views: 16954

Re: DM41X Beta Programme

Minor issue. Dialog displayed while in USB write mode states "Press EXIT key to end". Need to change as there is no "EXIT" key.
by jwhsu
Fri Feb 21, 2020 4:27 pm
Forum: Software issues
Topic: Cannot program byte grabber
Replies: 26
Views: 1246

Re: Cannot program byte grabber

@jwhsu - Have you tried with NO modules installed, as the instructions recommend? It is possible that having the printer module installed affects the memory conditions (perhaps it allocates a buffer, etc.) assumed to be fresh from reset in the instructions. And even if you had the 82143A printer pl...
by jwhsu
Fri Feb 21, 2020 1:12 pm
Forum: Software issues
Topic: Hepax/Zenrom conflict
Replies: 5
Views: 335

Hepax/Zenrom conflict

Combination of Hepax from Ángel’s files and Zenrom from hp41.org causes calc to freeze, requiring a hard reset. Load order on active module page is 1) Zenrom, 2) Hepax. Catalog-2 afterwards shows both modules installed with Hepax listing before Zenrom. HEPDIR showed “No Filesystem”. Turning the calc...
by jwhsu
Fri Feb 21, 2020 12:27 pm
Forum: Software issues
Topic: Cannot program byte grabber
Replies: 26
Views: 1246

Re: Cannot program byte grabber

Mark Hardman wrote:
Fri Feb 21, 2020 5:00 am
I can confirm the issue. The instructions are at: https://www.hpmuseum.org/prog/synth41.htm

I even set the DM41X to SLOW mode to ensure that the CAT 1, R/S step is timed correctly.
I used the instructions on MoHP that Mark linked to.
by jwhsu
Fri Feb 21, 2020 1:27 am
Forum: Software issues
Topic: Cannot program byte grabber
Replies: 26
Views: 1246

Re: Cannot program byte grabber

Tried on a 41CL, able to create the byte grabber program. Tried again on the DM41X with only the printing module installed. Managed to get to the point where the ALPHA string “?AAAAAA” had to be entered. On the 41CL, all characters were displayed and was able to successfully exit program mode to cre...
by jwhsu
Fri Feb 21, 2020 1:04 am
Forum: Update Announcements
Topic: Source for additional MOD files
Replies: 88
Views: 4291

Re: Source for additional MOD files

Ángel,

I think I found a discrepancy between the AMMC/OSX module and the manual. CAT”1 doesn’t bring up the selection menu as stated in the manual. CAT”0 however does bring up the menu. I assume this was a recent change that has not made it to the manual.