Search found 388 matches

by rprosperi
Tue Jan 21, 2020 2:58 am
Forum: DM1x/DM41
Topic: DM41X
Replies: 68
Views: 9306

Re: DM41X

Hee hee! I'd settle for any printer that used least 8.5" width on non-thermal paper. Even a laser printer would be nice. I have an HP LJ-2100 that has a built-in IR receiver, which works fine with several Sharp Wizard and Zaurus products, but sadly the IR output from the DM41X will not produce any ...
by rprosperi
Mon Jan 20, 2020 10:05 pm
Forum: DM1x/DM41
Topic: DM41X
Replies: 68
Views: 9306

Re: DM41X

toml_12953 wrote:
Mon Jan 20, 2020 9:00 pm
We don't use bar codes but printing to a real dot matrix printer would be great.
The 82440A/B is a real dot matrix printer :)

But I suppose you mean the type you can hear printing from 25 yards away...
by rprosperi
Fri Jan 17, 2020 7:22 pm
Forum: Firmware updates
Topic: Firmware V30 for DM1x/DM41(L) units
Replies: 8
Views: 503

Re: Firmware V30 for DM1x/DM41(L) units

DM15L and DM41L updated with no issues.

Thanks for the updates!
by rprosperi
Tue Jan 14, 2020 7:19 pm
Forum: DM1x/DM41
Topic: DM41X
Replies: 68
Views: 9306

Re: DM41X

Manual, what manual? This is a 41 near-clone, so everything should be obvious to even the most casual observer ("near" covering a world of possibilities here...)
by rprosperi
Mon Jan 13, 2020 11:08 pm
Forum: DM1x/DM41
Topic: DM41X
Replies: 68
Views: 9306

Re: DM41X

Walter wrote:
Mon Jan 13, 2020 10:25 pm
For #2, which part of my statement is incorrect? :?
You are correct that there is no Confirm on the 41CX, but your sense of smell needs some refinement.

Other hints will wait a day or so...
by rprosperi
Mon Jan 13, 2020 9:17 pm
Forum: DM1x/DM41
Topic: DM41X
Replies: 68
Views: 9306

Re: DM41X

Another guess: CST = CUSTOM ? But we have USeR already... :? CONF smells like CONFIRM but not seen on the HP-41Cx AFAIK. :? 1. Correct, but not the same as USER 2. Incorrect. 3. SIZE is the normal HP-41C SIZE command (to set the # of data storage registers). The slot was available so we figured bet...
by rprosperi
Sat Jan 04, 2020 12:03 am
Forum: DM42
Topic: Firmw update issue on Windows 10
Replies: 5
Views: 192

Re: Firmw update issue on Windows 10

The steps leading up to running dmtool are what is confusing though. Do I need to press F!/Reset for dmtool to see the DM42?? On the DM42, you need to press: Shift-Setup-5-2-2 to put the device into Bootloader mode. If already connected to the PC via cable when you do this (you should be), you shou...
by rprosperi
Fri Jan 03, 2020 11:58 pm
Forum: Update Announcements
Topic: UPDATE: DMCP-3.12 / DM42-3.12
Replies: 40
Views: 7859

Re: UPDATE: DMCP-3.12 / DM42-3.12

You are confusing versions of DMCP (the OS) and the DM42 Application.

Look carefully at the About screens and you will see the DMCP version in the 2nd line down and DM42 version in the 4th line down.
by rprosperi
Fri Jan 03, 2020 3:12 am
Forum: DM42
Topic: Firmw update issue on Windows 10
Replies: 5
Views: 192

Re: Firmw update issue on Windows 10

When you install the drivers under Windows-10, you must first disable driver signing enforcement, otherwise the driver installation does not properly complete installation, even though there were no errors. This web page explains how to disable signed driver enforcement: https://social.technet.micro...
by rprosperi
Wed Dec 18, 2019 11:12 pm
Forum: Discuss!
Topic: 43S News
Replies: 563
Views: 82082

Re: 43S News

@DiscoMike - My earlier post may not been clear on a key point. Although the 43S software is far from complete now, the manuals are probably 90-95% complete, including descriptions for all the features that have yet to be implemented. As development proceeds and new ideas and/or small issues arise, ...