Search found 34 matches
- Sat Feb 29, 2020 1:52 pm
- Forum: Software Library
- Topic: Matrix Viewer
- Replies: 22
- Views: 18146
Re: Matrix Viewer
Upper/lower case is no issue of course, that’s not what I meant by ‘topaligned’. It’s just that a font of n pixels occupies the top n pixels, not the bottom n. And sub- and superscript is similar: just swap the two adjustments? (The Y-adjustment for a bottom-aligned subscript is the negative of the...
- Fri Feb 28, 2020 8:28 pm
- Forum: Software Library
- Topic: Matrix Viewer
- Replies: 22
- Views: 18146
Re: Matrix Viewer
Werner, I would like to modify my routines to use your UFL matrix. That way only one font matrix for everyone. But I have some questions/comments: 1. It sounds like your final UFL matrix will have four font sizes. That would be fantastic. 2. I'm not sure about having the UFL matrix "top aligned...
- Fri Feb 28, 2020 6:48 pm
- Forum: Software Library
- Topic: Matrix Viewer
- Replies: 22
- Views: 18146
Re: Matrix Viewer
Hi Bill, Yes I realised there’s no easy way of copying a matrix to another state file, but I wanted to make it easy to take a peek. You don’t need UFL though, well not for now, I just put the digit fonts into DF, but the problem remains of course. One of my goals is to have UFL hold all 4 fonts, an...
- Fri Feb 28, 2020 4:34 pm
- Forum: Software Library
- Topic: Matrix Viewer
- Replies: 22
- Views: 18146
Re: Matrix Viewer
Werner, Could you post the raw file of the program that generates the "UFL" font file? I see this is a variation of the file I had done with a middle size font added for the digits 0-9. Also, what does the letters "UFL" stand for? Assume the "F" is for FONT. It's too ba...
- Wed Feb 19, 2020 5:03 pm
- Forum: Software Library
- Topic: Matrix Viewer
- Replies: 22
- Views: 18146
Re: Matrix Viewer
- Wed Feb 19, 2020 2:52 pm
- Forum: Software Library
- Topic: Matrix Viewer
- Replies: 22
- Views: 18146
Re: Matrix Viewer
I'm having a problem getting the state file to load. I get the message " State File Corrupt" I've downloaded it several times, used several programs to upzip it, done byte compares on the the original file versus what's on the DM42, did a fat check and reformat on the calculator. Other sta...
- Mon Jun 03, 2019 7:12 pm
- Forum: DM42
- Topic: Leather Case for DM42
- Replies: 16
- Views: 17902
Re: Leather Case for DM42
Or if you want to delve even deeper into nerd territory and have a 3D printer, here is a link to a hard case that I designed for the DM42: https://www.thingiverse.com/thing:3529736 I like the looks of the case you created. I was able to adapt the ASTECH Hard Case to the DM42. See my post in the fol...
- Fri May 10, 2019 5:04 pm
- Forum: DM42
- Topic: Thermal Paper?
- Replies: 10
- Views: 10331
Re: Thermal Paper?
Finally, it is "normal" for output to fade considerably, even after only a couple months, if the listings are left out and exposed to light. To preserve them, keep them in a file, or book, etc. to preserve the printout. I assume that you are preserving them so that you can look at them in...
- Sat Aug 25, 2018 9:46 pm
- Forum: DM42
- Topic: 3D printed DM42 stand
- Replies: 12
- Views: 9638
Re: 3D printed DM42 stand
The ASTECH case is fantastic. Perfect for protection in the field. Here's a closeup of the Hinge assembly. There are two pins that hold it together. Hinge.jpg The case is slightly too wide for the DM42 to fit. I was able to get a nice fit by cutting two lengths of the soft fabric side of Velcro. Put...
- Sat Aug 18, 2018 12:23 am
- Forum: SwissMicros Firmware Update Announcements
- Topic: UPDATE: DMCP-3.9a / DM42-3.9.1 / dm_tool-2.4
- Replies: 21
- Views: 24389
Re: UPDATE: DMCP-3.9a / DM42-3.9.1 / dm_tool-2.4
Thanks.
Update was quick and easy.
Bill
Smithville, NJ
Update was quick and easy.
Bill
Smithville, NJ